Oil Change Made Easy: Master the Art of Changing Gear Oil in Your PCX 160

Maintaining your Honda PCX 160 is crucial for ensuring its longevity and performance. One essential task is changing the gear oil, which lubricates the transmission components and helps prevent wear and tear. This guide will provide a step-by-step walkthrough on how to change gear oil in your PCX 160, ensuring its smooth and efficient operation.

Tools and Materials Required

Before you begin, gather the necessary tools and materials:

• New gear oil (recommended: Honda Genuine Gear Oil SAE 10W-30)
• Drain pan
• Funnel
• 17mm socket wrench
• 12mm socket wrench
• Torque wrench (optional)
• Rags or gloves

Safety Precautions

• Allow the engine to cool down before starting the procedure.
• Wear gloves to protect your hands from hot oil.
• Dispose of used oil and filters responsibly.

Step-by-Step Guide

1. Locate the Gear Oil Drain Plug

• Position the PCX 160 on a level surface.
• Locate the gear oil drain plug on the bottom of the engine case, near the left side.

2. Drain the Old Gear Oil

• Place the drain pan under the drain plug.
• Using the 17mm socket wrench, carefully loosen the drain plug.
• Allow the old gear oil to drain completely into the drain pan.

3. Remove the Oil Filter

• Locate the oil filter on the left side of the engine case, near the rear.
• Using the 12mm socket wrench, loosen the oil filter and remove it.
• Check the old oil filter for any metal shavings or debris.

4. Install the New Oil Filter

• Apply a thin layer of new gear oil to the rubber gasket of the new oil filter.
• Screw the new oil filter onto the engine case by hand until it is snug.
• Use the 12mm socket wrench to tighten the oil filter an additional 3/4 to 1 turn.

5. Reinstall the Drain Plug

• Clean the drain plug and its washer.
• Apply a small amount of new gear oil to the drain plug washer.
• Screw the drain plug back into the engine case and tighten it using the 17mm socket wrench.
• Torque the drain plug to 30 Nm (22 ft-lbs) if using a torque wrench.

6. Fill with New Gear Oil

• Using the funnel, pour the new gear oil into the engine case.
• The PCX 160 requires approximately 0.8 liters (0.21 gallons) of gear oil.

7. Check Gear Oil Level

• Start the engine and let it run for a few minutes.
• Stop the engine and wait a few minutes for the gear oil to settle.
• Check the gear oil level using the dipstick located on the left side of the engine case.
• The gear oil level should be between the “MIN” and “MAX” marks on the dipstick.

Maintenance Intervals

Honda recommends changing the gear oil in the PCX 160 every 12,000 kilometers (7,500 miles) or once a year, whichever comes first. However, more frequent oil changes may be necessary in severe riding conditions, such as frequent stop-and-go traffic or dusty environments.

Benefits of Changing Gear Oil

Regular gear oil changes offer several benefits for your PCX 160:

• Reduced Wear and Tear: Gear oil lubricates the transmission components, reducing friction and preventing premature wear.
• Improved Performance: Fresh gear oil helps maintain smooth gear shifting and clutch engagement.
• Extended Transmission Life: Regular oil changes help extend the lifespan of the transmission by removing contaminants and preventing corrosion.

Key Points: Maintaining Your PCX 160’s Transmission

Changing the gear oil in your PCX 160 is a relatively simple and inexpensive maintenance task that can significantly impact the overall health and performance of your scooter. By following these steps and adhering to the recommended maintenance intervals, you can ensure the smooth and efficient operation of your transmission for many miles to come.

Information You Need to Know

Q1: What is the recommended gear oil type for the PCX 160?

A: Honda Genuine Gear Oil SAE 10W-30

Q2: How much gear oil does the PCX 160 require?

A: Approximately 0.8 liters (0.21 gallons)

Q3: How often should I change the gear oil in my PCX 160?